SXDOOL Semiconductor Refrigerator Small Fish Tank Chillers Cycle Refrigeration Cooling Equipment 72W
Review: 5 - "A masterpiece of literature" by , written on May 4, 2006
I really enjoyed this book. It captures the essential challenge people face as they try make sense of their lives and grow to adulthood.

SXDOOL Semiconductor Refrigerator Small Fish Tank Chillers Cycle Refrigeration Cooling Equipment 72W

Available: In Stock
$160.75
Image

aeProduct.getSubject()

Friends and fisheries good helper!

[Name] 72W refrigerator
Technical parameters]
Voltage:AC220-240V/50-60Hz
Power:72W
Temperature set range:10~40

The applicable water pipes: inner diameter of 8mmWater pipes
Suitable for water flow:1-3L / minute

Suitable for lift:3mThe following
The length of the power cord: 1.5 MAndThreeFeet flat plug
Thermostat probe line length:2m
Dimensions:
22.5 * 18.5 * 15CM
[Origin of goods] Shenzhen
Introduction
· Mute, low-power design.
· Operation set is simple.
· Temperature displayed glance.
· Fresh water tank, planted aquarium, saltwater tank Universal.
Use
With the filtration drum or pumps use direct channeling even the middle of the water pipes installed in the water cycle.
Note
1.Transportation, installation, maintenance, etc. Please handle with care.
2.Machine with the surrounding space remains0cmDistance above, to facilitate airflow circulation cooling.
Weight2kg
Machine size: 22.5 * 18.5 * 15CM

aeProduct.getSubject()

aeProduct.getSubject()

aeProduct.getSubject()

Thermostat setting method

a,LED Status Description

H / CIndicator flashes to indicate cooling or heating delay, Always cooling or heating (snowflake).

Front light: Indicates the working status of the cooling, heating, Always on behalf of the Working representative of long off does not work.

b,Temperature control internal parameter descriptions and settings

The display panel KEYS: set keySet,Up key down key key to openRst

c,Temperature point set methods:

Under normal operating conditions, the key to openSetThree seconds, turn off the thermostat, click to open the key to open the thermostat, clickSetKey, shows the number of beats, the display value for the current state of the work of the temperature set value can increase or decrease the temperature setting, press or . Press or to quickly increase or decrease. No key operation state5Seconds to save the last setting to return to normal operation.

d,Cooling, heating mode selection method

Press the Setup buttonSetExceed5Seconds to enter the menu screen appears "HC"The code, press the Set buttonSet,Displayed for the current state of work setting, press the up key or down button to change the settings. No key operation state10Seconds to return to normal operation.

e,Operating parameters setting method:

Press the Setup buttonSetExceed5Seconds to enter the menu display, when the screen appears "HCCode, press the up key or down key to switch the displayHCAndD ---- ptMenu code. To change the parameter values, and so the switch to the appropriate menu code, click set keySet,The value for the current work status settings can change the settings, press or . Hold it down, can quickly increase or decrease. No key operation state10Seconds to return to normal operation.

Parameter table:

Parameter

Function Description

Setting range

The factory setting

HC

Refrigeration/Heating

COrH

C

D

Hysteresis setting

1 - 5

3

LS

The upper limit of the lowest setting

-50 -Set point

25

HS

Maximum cap on

Set point- 110

28

CA

Temperature correction

-7-7

0

PT

Refrigerator delayed start time

0 - 7

0

f,Parameter Function Description:

1, the temperature correction: When measuring temperature and standard temperature deviation, using this feature, the machine measured values can be adjusted consistent with the standard temperature, the temperature after the correction=Temperature before the correction+Correction value.

2, cooling, heating function:

Cooling mode: When the temperature set point temperature measurement value ≥+Hysteresis, refrigeration relay pull chiller start; When the temperature set point temperature measurement value ≤ refrigeration relay disconnected, the refrigerator stopped working.

Heating mode: When the temperature set point temperature measurement value ≥+Hysteresis heating relay is disconnected, the refrigerator stopped working; relay is energized when the temperature measurement value ≤ temperature set point, the heating, chillers start.

3, chillers delay start time:

Cooling mode: first powered on, if the current temperature is greater than the temperature set value+Hysteresis, the refrigerator will not immediately start cooling, need to run to set the delay time to start.

Heating mode: first powered on, if the current temperature is less than the temperature set value+Hysteresis, the refrigerator does not immediately start the heating needs to start after the delay time set by the run.

Chiller downtime between adjacent two starts delayed start time setting interval is greater than the refrigerator, the refrigerator starts immediately.

The refrigerator adjacent down time interval between two starts less than chillers delay setting need to run to finish the set refrigerator after a delayed start time setting the machine to start, chiller start. The delay time from stop instantly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 "Thank you for your visit! Welcome come again!

aeProduct.getSubject()

aeProduct.getSubject()

Friends and fisheries good helper!

[Name] 72W refrigerator
Technical parameters]
Voltage:AC220-240V/50-60Hz
Power:72W
Temperature set range:10~40

The applicable water pipes: inner diameter of 8mmWater pipes
Suitable for water flow:1-3L / minute

Suitable for lift:3mThe following
The length of the power cord: 1.5 MAndThreeFeet flat plug
Thermostat probe line length:2m
Dimensions:
22.5 * 18.5 * 15CM
[Origin of goods] Shenzhen
Introduction
· Mute, low-power design.
· Operation set is simple.
· Temperature displayed glance.
· Fresh water tank, planted aquarium, saltwater tank Universal.
Use
With the filtration drum or pumps use direct channeling even the middle of the water pipes installed in the water cycle.
Note
1.Transportation, installation, maintenance, etc. Please handle with care.
2.Machine with the surrounding space remains0cmDistance above, to facilitate airflow circulation cooling.
Weight2kg
Machine size: 22.5 * 18.5 * 15CM

aeProduct.getSubject()

aeProduct.getSubject()

aeProduct.getSubject()

Thermostat setting method

a,LED Status Description

H / CIndicator flashes to indicate cooling or heating delay, Always cooling or heating (snowflake).

Front light: Indicates the working status of the cooling, heating, Always on behalf of the Working representative of long off does not work.

b,Temperature control internal parameter descriptions and settings

The display panel KEYS: set keySet,Up key down key key to openRst

c,Temperature point set methods:

Under normal operating conditions, the key to openSetThree seconds, turn off the thermostat, click to open the key to open the thermostat, clickSetKey, shows the number of beats, the display value for the current state of the work of the temperature set value can increase or decrease the temperature setting, press or . Press or to quickly increase or decrease. No key operation state5Seconds to save the last setting to return to normal operation.

d,Cooling, heating mode selection method

Press the Setup buttonSetExceed5Seconds to enter the menu screen appears "HC"The code, press the Set buttonSet,Displayed for the current state of work setting, press the up key or down button to change the settings. No key operation state10Seconds to return to normal operation.

e,Operating parameters setting method:

Press the Setup buttonSetExceed5Seconds to enter the menu display, when the screen appears "HCCode, press the up key or down key to switch the displayHCAndD ---- ptMenu code. To change the parameter values, and so the switch to the appropriate menu code, click set keySet,The value for the current work status settings can change the settings, press or . Hold it down, can quickly increase or decrease. No key operation state10Seconds to return to normal operation.

Parameter table:

Parameter

Function Description

Setting range

The factory setting

HC

Refrigeration/Heating

COrH

C

D

Hysteresis setting

1 - 5

3

LS

The upper limit of the lowest setting

-50 -Set point

25

HS

Maximum cap on

Set point- 110

28

CA

Temperature correction

-7-7

0

PT

Refrigerator delayed start time

0 - 7

0

f,Parameter Function Description:

1, the temperature correction: When measuring temperature and standard temperature deviation, using this feature, the machine measured values can be adjusted consistent with the standard temperature, the temperature after the correction=Temperature before the correction+Correction value.

2, cooling, heating function:

Cooling mode: When the temperature set point temperature measurement value ≥+Hysteresis, refrigeration relay pull chiller start; When the temperature set point temperature measurement value ≤ refrigeration relay disconnected, the refrigerator stopped working.

Heating mode: When the temperature set point temperature measurement value ≥+Hysteresis heating relay is disconnected, the refrigerator stopped working; relay is energized when the temperature measurement value ≤ temperature set point, the heating, chillers start.

3, chillers delay start time:

Cooling mode: first powered on, if the current temperature is greater than the temperature set value+Hysteresis, the refrigerator will not immediately start cooling, need to run to set the delay time to start.

Heating mode: first powered on, if the current temperature is less than the temperature set value+Hysteresis, the refrigerator does not immediately start the heating needs to start after the delay time set by the run.

Chiller downtime between adjacent two starts delayed start time setting interval is greater than the refrigerator, the refrigerator starts immediately.

The refrigerator adjacent down time interval between two starts less than chillers delay setting need to run to finish the set refrigerator after a delayed start time setting the machine to start, chiller start. The delay time from stop instantly.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 "Thank you for your visit! Welcome come again!

aeProduct.getSubject()

SHIPPING

All orders will ship between 1-3 Business Days (unless unexpected circumstances occur)

Please allow 15-25 Business Days for arrival for standard shipping (some international orders may require 30-60 days in some cases due to customs/local post office delays)

Express shipping packages will normally arrive within 6-8 business days or faster.(some international orders may require 15-20 days in some cases due to customs/local post office delays)

We ship internationally from our warehouses in China and the U.S.
We automatically calculate which shipping method will be the fastest to your location.
During the holidays, please allow extra time for delivery.

Business days are Monday through Friday 8AM-10PM. (Weekends and Holidays are not considered Business Days)

Please note - if you email our customer support during the weekends, you will receive a response on the next business day. 

Please note - if you select DHL service and it is not available in your area, we will contact you and provide a different carrier

We are not responsible for deliveries that were attempted but not successful because there was no one home or available to give a signature.

We are not responsible for unsuccessful delivery attempts that result in a return to sender situation.

We are not responsible for incorrect addresses entered into our shipping form.

After a package is shipped out, we are unable to modify the delivery address.

Our reship fee is $15 (some larger orders may require a higher reship fee) and is subject to policies above.

50% refunds (if applicable)
In some cases, we may issue a 50% refund if there's a delivery issue caused by the customer and the customer requests to not reship. We reserve the right to review each scenario and deem if a 50% refund is applicable.

If packages are stolen, please provide us proof of theft and we will reship a new package to you at no charge.

We are not responsible for delays caused by customs, or unexpected postal delivery delays such as local postal backlogs or strikes.
We are not responsible for customs fees for international customers.

We always try our best to estimate the shipping time and communicate with complete transparency with our customers, but sometimes unforeseen problems occur.

We thank you for your understanding and hope you love your product from COOLINGFANSTORE!!

Returns 
Our policy lasts 30 days. If 30 days have gone by since your purchase, unfortunately we can’t offer you a refund or exchange. 

To be eligible for a return, your item must be unused and in the same condition that you received it. It must also be in the original packaging. 

Several types of goods are exempt from being returned. Perishable goods such as food, flowers, newspapers or magazines cannot be returned. We also do not accept products that are intimate or sanitary goods, hazardous materials, or flammable liquids or gases. 

Additional non-returnable items: 
- Gift cards 
- Downloadable software products 
- Some health and personal care items 

To complete your return, we require a receipt or proof of purchase. 
Please do not send your purchase back to the manufacturer. 

There are certain situations where only partial refunds are granted (if applicable) 
- Book with obvious signs of use 
- CD, DVD, VHS tape, software, video game, cassette tape, or vinyl record that has been opened 
- Any item not in its original condition, is damaged or missing parts for reasons not due to our error 
- Any item that is returned more than 30 days after delivery 

Refunds (if applicable) 
Once your return is received and inspected, we will send you an email to notify you that we have received your returned item. We will also notify you of the approval or rejection of your refund. 
If you are approved, then your refund will be processed, and a credit will automatically be applied to your credit card or original method of payment, within a certain amount of days. 

Late or missing refunds (if applicable) 
If you haven’t received a refund yet, first check your bank account again. 
Then contact your credit card company, it may take some time before your refund is officially posted. 
Next contact your bank. There is often some processing time before a refund is posted. 
If you’ve done all of this and you still have not received your refund yet, please contact us at c_fan123@hotmail.com. 

Sale items (if applicable) 
Only regular priced items may be refunded, unfortunately sale items cannot be refunded. 

Exchanges (if applicable) 
We only replace items if they are defective or damaged. If you need to exchange it for the same item, send us an email at c_fan123@hotmail.com and send your item to: Sensda Electronics Limited, No.20 GuanDA road Huangpu District Guangzhou, 510000 广东, 中国. 

Gifts 
If the item was marked as a gift when purchased and shipped directly to you, you’ll receive a gift credit for the value of your return. Once the returned item is received, a gift certificate will be mailed to you. 

If the item wasn’t marked as a gift when purchased, or the gift giver had the order shipped to themselves to give to you later, we will send a refund to the gift giver and he will find out about your return. 

Shipping 
To return your product, you should mail your product to: Sensda Electronics Limited, No.20 GuanDA road Huangpu District Guangzhou, 510000 广东, 中国 

You will be responsible for paying for your own shipping costs for returning your item. Shipping costs are non-refundable. If you receive a refund, the cost of return shipping will be deducted from your refund. 

Depending on where you live, the time it may take for your exchanged product to reach you, may vary.